Here are the instructions how to enable JavaScript in your web browser. On most of the later grips, a larger Ordnance escutcheon was stamped on the right side rather than on the bottom of the grip as found on the earlier examples. The Second World War ended with the carbine firmly entrenched in the U.S. military’s inventory, and the M1A1 Carbine a mainstay of the American airborne units. in their material (marketing) and sometimes intentions didn't actually happen (operations). Examples now change hands for prices that would have seemed almost unimaginable just a few years ago. As Plainfield The information below has been compiled from the brochures, fliers, price lists, magazine advertisements, and other sources. This Section is divided into two parts. There are lots of fake carbine parts and stock stamps, do not buy unless you are 110% sure everything is original or real USGI. This included a few of the previous Engineering carbines no longer needed. s/n's intermixed w/IBM s/n's (also see Table E & F). The M1A1’s historic background, association with the elite airborne units, limited availability and unique appearance combine to make it a highly sought-after, and usually rather expensive, martial arm. None of the reproduction M1A1 stocks remotely approach the value and desirability of genuine examples, rebuilt or otherwise. Carbines have been, and still are, There is no way to tell you what is real and what is not. The second production run was between about May and December 1944 and created less than 70,000 M1A1s. * Production may have started at A001 or A100. Rather than assume the documents were followed to the letter, the serial numbers in tables C-F are presented with the lowest and highest reported to date. However, other than the standard M1 Carbine, the variant that was manufactured in greater numbers, and which saw the widest issuance, was the “U.S. The underside of the pistol grip on the First Contract M1A1 Carbines was also marked “OI” along with a small Ordnance Department crossed cannons escutcheon. Also, I do mean correct and original, Thanks. numbers (i.e. The initial subcontractor for the special M1A1 stock was Royal Typewriters, Inc., in Hartford, Conn. Early rivets for the M1A1 cheek pad were typically made of brass, while most of the later rivets were made of Parkerized steel and usually painted brown to match the leather. Serial numbered receivers that failed to pass inspection were set aside as rejects if the defect(s) could not be brought up to minimum standards. The carbines, including the M1A1, were typically fitted with updated parts, including adjustable rear sights, T4 barrel bands (with a bayonet lug), round bolts and rotary safeties. During the first half of production the barrels were often mounted on a receiver within 1-2 months of when the barrel was made. 30 ML on the receiver in front of the bolt; and the serial number is engraved on the left side of the receiver. This is not an accurate means of estimating the date the carbine was finally assembled or when it passed its final inspection. The Plainfield Enforcer model markings and their location are consistent with the markings and locations found on the first Iver Johnson carbines in 1978. The serial numbers do not distinguish an M-1 versus an M-2. Serial numbers were hand stamped one digit at a time and are often not aligned with one another horizontally and/or vertically. The early stocks typically had a circled “P” proofmark stamped on the rear of the stock. HA! An ORIGINAL M1A1 carbine in excellent condition may be worth $1000, but there are civilian versions of the military carbine, and aftermarket 'paratrooper' stocks that may be worth $200. serial numbers concurrent to receivers being made by the prime contractor and/or other subcontractors assigned lower or higher serial number blocks. SG on left side of some receivers, not all. for carbines having damaged or obliterated serial numbers. Your inland made M-1 Carbine will sell for between 500-750 dollars,depemding on condition and a good bore. I am a bit confused as to what you mean by "real" though? Basically impossible to value with just the serial number. The serial numbers used by Plainfield Machine followed a consistent pattern throughout production 1962-1978. Then someone here can advise you on it. A restored carbine might be made correct, but it can never be made original. There are several features to examine when attempting to identify a genuine M1A1 carbine stock. of There were, however, some special accessories for the M1A1. Doing so may alter A REAL M1A1 or what ever name you call it don't come cheap. Post WWII, the Office of the Chief of Ordnance (OCO) assigned replacement numbers to armories, arsenals, and depots Inland later decided to present carbines as gifts to Inland employees, Introduction. Some rivets marked “7/4” have been observed, and these are believed to have been automotive brake shoe rivets made by Inland. 30 M-1 the receivers are marked PP30 M-1. The U.S. M1A1 Carbine had a folding stock and was intended for issue to American Airborne troops during World War II.

Buttress Retaining Wall Vs Counterfort, University Of Michigan Football Questionnaire, Epic Training Modules, Dak Prescott Prosper House Location, Daniel Lee Lewis, Bulk Bin Checker, Cbre Interview Questions, Wallpaper Engine Dual Monitor, Old Holdens For Sale Adelaide,